It depends on car make, model and year of your vehicle. Sometimes they are the same sizes while other times they are not. Consult your owners manual or the catalog when purchasing replacement blades to make sure you purchase the correct size blades.
Different vehicles with different wiper sizes. You always confused by wiper sizes when you buying wipers.
There are various indications for worn-out wipers; streaks, smears, unwiped areas on the windshield; chattering, skipping wiper blades; nicked, cracked or separated rubber elements; noisy wiping action due to worn-out wiper blade joints.
If your blade is not aerodynamically designed , the air pressure around the blade will cause it to lift, right off the windshield, like an airplane wing. So when you choose a wiper blade shall consider its aerodynamic spoiler.
All of BAOYI wiper blade with aerodynamic design, it prevents wiper blades lift off the windshield at high speeds very well!
First, with a soft cloth, clean the windshield and wiper blades using a mixture of baking soda, dishwashing liquid and water.
Next, make sure the wiper blade is correctly installed using the proper adapter.
If the problem continues, adjust the tension by stopping the blades in the upright position. Hold blade at the point of connection to the arm and pull the blade away from the glass approximately two inches. Let the blade snap back to the glass. This process may need to be repeated a couple of times depending on the situation.
Raise the metal wiper arm away from the windshield. It should be able to hold steady in a position perpendicular to the windshield. Be careful with the positioning; the metal wiper arm is spring-loaded, and it could snap back and crack your windshield.
Unhook the old wiper blade. Look at the joint where the rubber wiper blade meets the metal arm. There should be a small plastic stopper holding the blade in place. Press the stopper and unhook the old wiper blade to separate it from the metal arm.
Some wiper blades have pins to hold the rubber wiper blade in place, rather than a hook.
Make sure one hand is holding the wiper away from the windshield during this entire process.
You may want to protect your windshield with a folded towel, just in case you the arm snaps back while you're trying to change the wiper.
Insert the new wiper. Slide the refill wiper into the same end of the arm where you pulled the old wiper out. Gently pivot the new wiper until the hook snaps into place to secure it. Lay the wiper back against the windshield.
Driving can be extremely distracting if the windshield wipers go squeaking all the time. The feeling is just opposite to that of hearing a pleasant music. Sometimes, the driver can just not concentrate on driving and thus, the passengers can see hell.
Therefore, you should know how to stop the wipers from squeaking and should thus practice a minimum maintenance that would demand you to just extract few minutes of your precious time.
To know how to stop the wipers from squeaking, you should know why they squeak. This can help you easily identify the exact problem and find the solution very easily.
Main Reasons That Cause The Wipers To Squeak:
Accumulation of dirt
Wipers are mainly constructed to wipe the windshield that is made of glass. If there is an accumulation of dust particles or other tough contamination on the windshield, the wipers that work to wipe the glass will not go smooth, thus irritating with squeaks.
The wiper assembly should be positioned enough to not to allow the air to enter between the windshield and the wiper blades, which might otherwise end up in squeaking.
Over usage might tear or under usage might brittle the wiper blades. Both the reasons end up in squeaking.
If there are any manufacturing defects be it in the rubber blades or in the screwing system, the result is squeaking.
However, if you need better wiper blades, please choose BAOYI wiper blades, enjoy clear view and silent.
Examine the wipers for cracks. Old windshield wipers become hard and cracked over time, especially in hot, dry climates. If your wiper seems to have lost it's rubbery spring, it's probably time to replace it.
Pay attention next time it rains. If your wipers leave streaks of water across your windshield that aren't much easier to see through than pounding rain, their rubber has probably lost its grip.
Now you know that why the wipers squeak, you should now know how to stop them from doing so.
Always keep the windshield clear from dust and other contamination. For that, clear it thoroughly with any one of the following products:
Dip a soft cotton cloth in vinegar and wipe the windshield gently to remove all the accumulated dirt.
* Baking Soda
Damp the dry powder on paper towel and wipe the windshield to clear all the contamination.
Dip a soft cotton cloth into the chemical and wipe the windshield carefully to remove the dirt.
2. Ensure that you replace the wiper blade refills regularly, at least once in a year, every time before the rainy season arrives. This is not an expensive maintenance and so you can you can prefer doing it instead of getting irritated with squeaks.
3. Ensure that the windshield wiper fluid is at appropriate levels or else they might end up in skipping, thus creating squeaks.
4. Ensure that the windshield wiper blades are soft. Maintain them to be free from either moisture or dryness. In either case, the rubber gets damaged, thus squeaking while wiping the windshield.
To make the wiper blades softer while being free from dust and other contaminants, clean the blades with any one the following chemicals:
5. Ensure that you do not over use chemicals like WD-40 as it is a petroleum based chemical. Such chemicals when over used will eat away the rubber, thus crumbling and damaging them.
Also, do not use them frequently, as it might dry the rubber, leaving it brittle. Therefore, the rubber loses its softness and might tear. Instead, try using rubbing alcohol as an alternative to WD-40 as it is comparatively milder and does not damage the wiper blades.
Ensure that the wiper blades are free from Rain-X or wax, as they can create a layer while wiping, thus squeaking.
7. When the wipers age out, replace the complete wiper assembly. This is because, with time, trauma and use, the assemblies that hold the wiper refills can get displaced from the actual position.
Also, the rubber of the wipers can be torn out as it ages, to no longer adapt to the contours of the windshield.In such situations, you have no choice other than replacing the complete assembly with new one.
Squeaking wipers would definitely result in an irritating experience for both the driver and the passengers. Nobody would love to experience it. However, simple and affordable maintenance would help you to avoid such displeasure experiences and enjoy pleasant driving.Ensure that the wipers are free from damage, brittle, dry, moisture and defects. Also, ensure that the windshield glass is always clean from dust particles. Make a regular check of wiper blade assembly to ensure that it is not misplaced.
If the wipers age out and are worn, replace the assembly with new one. These simple steps can prevent you from hearing squeaks and you can experience the joy of great drives.
If you can’t properly connect your blades to your car’s wiper blade fitting, you’re in trouble. Most modern wiper blades come with everything you need to connect your blade to your car, and many come with several different attachments for fittings that are uncommon or unusual. For older car models, there are three types of connectors for your wiper blades:
Side Pin: small pin on the wiper arm that connects the wiper arm to the blade
Bayonet: flat and square piece of metal that slides into the wiper blade attachment
Hook: curved shaped hook that goes around the blade
These are the connectors for traditional wiper blade devices. Traditional blade devices have a rubber blade at the long end of a somewhat complex, pressure sensitive and flexible metal frame. Newer cars may utilize a new type of blade technology. These are called beam blades. They are composed of an almost entirely plastic and triangular-shaped frame. The frame and blade are thinner, more aerodynamic, and apply more pressure across the windshield. If your car is designed for this type of blade, the following connectors apply:
Pin and Hook: composed of a small pin that fits into the wiper arm, and a hook that holds the pin in place.
Balanced Bayonet: a clamp on the arm that fits into place on the blade.
Pinch Tab: the blade moves into position is released through pressure applied to both sides of the arm.